manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 5 / 118

Поделиться
Скачать
GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 5

2

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Use Safety Chains

Use safety chains to help control drawn machinery should it 

separate from tractor drawbar or trailing nurse tank hitch.
Use chain with a strength rating equal to or greater than 

the gross weight of towed machinery.
Attach implement chain to tractor drawbar support or 

specified anchor location. Attach nurse tank chain(s) to 

anchors provided on implement. Allow only enough slack in 
chain for turns.
Replace chain if any links or end fittings are broken, 
stretched or damaged.
Do not use safety chain for towing.

Wear Protective Equipment (PPE)

Wear clothing and equipment appropriate for the job. Avoid 

loose-fitting clothing.
Waterproof, wide-brimmed hat.
Face shield, goggles or full face respirator. 
Prolonged exposure to loud noise can cause hearing 
impairment or loss. Wear suitable hearing protection such 

as earmuffs or earplugs.
Avoid wearing entertainment headphones while operating 

machinery. Operating equipment safely requires the full 

attention of the operator.
Goggles with side shields or a full face respirator is 

required if handling or applying dusts, wettable powders, or 
granules.
Cartridge-type respirator approved for pesticide vapors 
unless label specifies another type of respirator.
Waterproof, unlined gloves. Neoprene is recommended.
Cloth coveralls/outer clothing changed daily; waterproof 
items if there is a chance of becoming wet with spray.
Waterproof apron.
Waterproof boots or foot coverings.
Do not wear contaminated clothing. Wash protective 

clothing and equipment with soap and water after each use. 

Personal clothing must be laundered separately from 
household articles.
Clothing contaminated with certain pesticides must be 
destroyed according to state and local regulations. Read 

chemical label for specific instructions.

Содержание 3S-4000HD























































































































Отзывы:

Нет отзывов