GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 80

Страница: 80 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Maintenance and Lubrication

2019-03-14

Table of Contents Index

195-067M

Bleeding Fold Hydraulics

Refer to Figure 84

1. Review warnings, bleeding notes and system

information on page 75.

2. With drill unfolded and fold cylinders completely

extended, disconnect rod end pins and swing the

cylinders so they will not contact anything when

extended.

3. Loosen rod end hose JIC fitting

at elbow on right

fold cylinder.

4. Slowly supply oil to rod end of fold cylinders until oil

appears at loosened hose fitting. Tighten fitting and

completely retract fold cylinders.

5. With cylinders completely retracted, loosen base end

hose JIC fitting

at elbow on right fold cylinder.

6. Slowly supply oil to base end of fold cylinders until oil

appears at loosened hose fitting. Tighten base end

hose fitting and cycle fold cylinders in and out

several times.

7. Re-pin cylinder rod clevis.

Figure 84

Bleeding Fold Hydraulics

18958

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 80 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: