GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 53

Страница: 53 / 118

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Passcode

The passcode function allows you to protect:

- the total acre count,

- pulses per mile and

- width

settings with a 4-digit passcode. This prevents accidental

and malicious changes to those settings. As provided by

the factory, the passcode feature is disabled, and you

can modify those function values at any time.
Press the FUNC button until the “PASS” legend appears.

The display reads either:

“

Net

” (enter passcode) or

“

diS

” (passcode disabled)

Enable and Set Passcode

The PASS display must show “

diS

” in order to enable

and set a passcode on a unit which presently has no

passcode (see below for changing an existing

passcode).

Refer to Figure 52

Use the UP and DOWN buttons to select a passcode in

the range 0001 through 9999 (0000 disables).
Press FUNC to accept the passcode. If the module

enters sleep mode before you press FUNC, the

passcode is not set.
Note: The protected function values remain unprotected

until the next time the module enters sleep mode.

Using a Passcode

If the PASS display shows “

Ent

”, a passcode must be

entered, or the protected function values cannot be

changed.

Refer to Figure 53

Enter the passcode using the UP and DOWN buttons.

When your passcode is displayed, press the FUNC

button to test the passcode.
If the passcode is correct, you can change the protected

settings.
The protected settings are unprotected, and the

password remains viewable in the PASS display

function, until the module next enters sleep mode. When

FUNC is next pressed, the passcode is again required to

change protected settings.
If the entered passcode is not correct, the protected

settings cannot be changed. When the “PASS” function

is selected again, “

Ent

” appears in the display.

Figure 52

Password Presently Disabled

26479

6 of 8

Figure 53

Password Prompt

26479

7 of 8

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 53 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: