GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 72

Страница: 72 / 118

2019-03-14

Table of Contents Index

195-067M

Great Plains Manufacturing, Inc.

Table of Contents Index

Troubleshooting

Problem

Cause

Solution

Planting too much

Incorrect seed rate or drive type.

Check seed rate information in Seed

Rate Manual.

Seed size and weight may vary.

Adjust seed rate handle.

Actual field size is different.

Verify field size.

Excessive overlap.
Irregular shaped field.

Adjust marker, page 24.

Incorrect tire size or air pressure.

Correct tire size and air pressure,

page 103.

Seed cup door open too much.

Refer to Seed Rate Manual.

Planting too little

Incorrect seed rate or drive type.

Check seed rate information in Seed

Rate Manual.

Excessive field speed.

Reduce field speed.

Seed size and weight may vary.

Adjust seed rate handle.

Incorrect tire size or air pressure.

Correct tire size and air pressure,

page 103.

Check seed level in seed box.

Fill seed box.

Actual field size is different.

Verify field size.

Excessive gaps between drill passes.

Adjust marker, page 24.

Build up of seed treatment in seed

cups.

Clean out seed cups.

Plugged opener seed tube.

Lift drill, expose bottom of seed tube

and clean out.

Obstruction in seed cup from foreign

matter or unclean seed.

Clean seed cup.

Thrown or worn drive chains

Check drive chains.

Worn sprockets and/or chain idlers.

Replace sprockets and/or chain idlers.

Uneven seed depth

Excessive field speed.

Reduce field speed.

Planting conditions too wet.

Wait until drier weather.

Seed-Lok

building up with dirt.

Lock up Seed-Lok

, page 64.

Damaged or missing seed flaps.

Replace seed flaps.

Partially plugged opener seed tube.

Lift up drill, expose bottom of seed

tube and clean out.

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 72 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: