GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 92

Страница: 92 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Maintenance and Lubrication

2019-03-14

Table of Contents Index

195-067M

Seed Flap Replacement

Current Solid Flap Replacement

Refer to Figure 105

To replace a seed flap , use needle nose pliers or

similar tool to grasp “T” top of flap. Pull upward to

remove flap from metal bracket .
Push new seed flap down through metal bracket until

flap snaps into place with “T” top resting on top of

bracket.
If a seed firmer is also installed, it may be necessary to

shorten the flap.

Older Split Flap Replacement

Refer to Figure 106

To replace an older split-style seed flap

use a needle

nose or similar tool and squeeze the tabs

together.

Pull plastic seed flap

down out of metal bracket

Push new seed flap

up through metal bracket

until

tabs

on seed flap snap in place.

Figure 105

Solid Seed Tube Flap

19398

Figure 106

Split Seed Tube Flap

18398

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 92 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: