GREAT PLAINS 3S-4000HD Скачать руководство пользователя страница 33

Страница: 33 / 118

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Transport

Loss of Control Hazard:

Towing the drill at high speeds or with a vehicle that is not

heavy enough could lead to loss of vehicle control. Loss of
vehicle control could lead to serious road accidents, injury

and death. To reduce the hazard:

Do not exceed 20 mph.

Do not tow a drill that, when fully loaded, weighs more than
1.5 times the weight of the towing vehicle.

In the following table, multiply the total drill weight by

0.67 (



) to determine minimum tractor weight.

Tractor Requirements

Marker Transportation

Refer to Figure 23

Always transport markers folded flat. Make sure second

marker section rests securely on transport carrier.

Drill Weight (Pounds / Kilograms)

Drill Model

3S-4000HD-7806

3S-4000HD-6375

3S-4000HD-4810

Standard “

” Drill

21734 lbs / 9858 kg

20834 lbs / 9450 kg

19934 lbs / 9042 kg

For “

HDF

” Model, add...

+1337 lbs / +607 kg

+1308 lbs / +593 kg

+1279 lbs / +580 kg

With Single Markers, add...

+1016 lbs / +461 kg

With Dual Markers, add...

+1997 lbs / +906 kg

For Full Seed Load, add...

+8294 lbs / +3762 kg

Maximum Configuration

(HDF, Dual Markers, Seed Loaded)

33363 lbs / 15133 kg

32433 lbs / 14712 kg

31504 lbs / 14290 kg

Figure 23

Marker in Transport Cradle

18857

Содержание 3S-4000HD























































































































Результаты поиска

Содержание 3S-4000HD

Отзывы:

GREAT PLAINS 3S-4000HD, Руководство оператора, Страница: 33 / 118

Результаты поиска

Содержание 3S-4000HD

Отзывы: