GREAT PLAINS 1510P Скачать руководство пользователя страница 61

Страница: 61 / 146

1510P & 1520P

Table of Contents

Index

Maintenance and Lubrication

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

Refer to Figure 62

Check for excess wear on meter slide (1). Slight
wear at the top corner is normal.

If slide is not excessively worn, stop here. If it is,
continue with the following steps to replace.

Refer to Figure 63

Remove retaining clip and pin from meter.



NOTE: Meter slide is spring loaded and the two

meter slide springs will be released when you pull

the pin. Use care not to lose pins and springs.

Check removed pin for wear and replace if worn.

Refer to Figure 64

10. Remove meter slide (1) with springs (2).

11. Place springs in new meter slide and install in

meter.

12. Reinstall seed meter wheel. Refer to page 35.

Figure 61

Meter Slide Location

18269

Figure 62

Meter Slide Location

Figure 63

Meter Slide Retaining Clip

19190

Retaining

Clip

18269

Figure 64

Meter Slide

Содержание 1510P



















































































































































Результаты поиска

Содержание 1510P

Отзывы:

Похожие инструкции для 1510P

Бренды по названию

Популярные бренды

GREAT PLAINS 1510P, Руководство оператора

Результаты поиска

Содержание 1510P

Отзывы:

Похожие инструкции для 1510P

Бренды по названию

Популярные бренды