GREAT PLAINS 1510P Скачать руководство пользователя страница 57

Страница: 57 / 146

1510P & 1520P

Table of Contents

Index

Adjustments

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

Press wheels not compacting

the soil as desired

Too wet or cloddy.

Wait until drier weather or rework

ground.

Coulter set too shallow.

Check coulter adjustment in hitch

operator’s manual.

Drill not running level front-to-back in

the field.

Readjust top link to level drill.

10 Series Openers - incorrect press

wheel depth setting.

Check opener adjustment, page 26.

Opener spring pressure too high.

Reduce opener spring pressure.

20 Series Openers - not enough pres-

sure on press wheels.

Check opener adjustment, page 26.

Excessive seed cracking

Excessive field speed.

Slow down. Check Seeding Rate Chart

for correct maximum field speed.

Unclean seed.

Use clean seed.

Incorrect seed meter wheel.

Change seed meter wheel, page 35.

Incorrect seed size for seed meter

wheel.

Verify seed count on seed bag with

seed meter wheel.

Build up of seed treatment in seed

meter wheel pockets.

Clean seed meter wheel. Add more

talc lubricant.

Worn or damaged seed meter wheel.

Replace seed meter wheel.

Worn or damaged meter slide.

Replace meter slide, page 55.

Damaged, old or dry seed.

Use clean, new seed.

Drill boxes do not empty evenly

Right and left hand seed rates are not

set the same.

Readjust rates, see Seed Rate Charts

page 107

Tire sizes or tire inflation not equal on

right and left gauge wheels.

Correct tire size or tire inflation, page

137.

Meter(s) are shut off.

Open meter(s).

Opener seed tube plugged.

Lift up drill, expose bottom of seed

tube and clean out with wire.

Sliding seed tube plugged.

Clean out sliding seed tube.

Drive chains damaged or missing.

Replace drive chains.

Drive torque requirements different on

right and left gauge wheel drives.

Check gauge wheels and tires.

Unequal number of sliding seed tubes

in each box compartment.
Planting around fields vs. back-and-

forth.

Correct planting operation.

Rough field conditions may move

seed in the box.

Problem

Cause

Solution

Содержание 1510P



















































































































































Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510P, Руководство оператора

Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды