GREAT PLAINS 1510P Скачать руководство пользователя страница 58

Страница: 58 / 146

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

1510P & 1520P

Table of Contents

Index

Adjustments

Press wheel or openers plug-

ging

Planting conditions too wet.

Wait until drier weather.

Drill not running level front-to-back in

the field.

Readjust top link to level drill.

Drill frame height incorrect.

Adjust drill frame height, page 31.

Coulters not set deep enough to cut

residue.

Check coulter adjustment in hitch

operator’s manual.

Opener set too deep.

Readjust, page 26 or page 28.

Opener spring force too high.

Readjust, page 26 or page 28.

20 Series Openers press wheel spring

force too high.

Readjust, page 28.

20 Series Openers 1 x 12 press wheel

stagger adjustment not correct.

Correct press wheel stagger.

Backed up with drill in the ground

Clean out and check for damage.

Failed disk bearings

Replace disk bearings.

Disk blades worn.

Adjust or replace disk blades, page

62.

20 Series Opener side depth wheels

not adjusted correctly.

Readjust, page 71.

Scraper worn or damaged.

Replace scraper.

Drill is not pulling level front-to-

back

Incorrect top link adjustment.

Readjust top hitch link to level drill.

Hydraulic marker functioning

improperly

Air or oil leaks in hose fittings or con-

nections.

Check all hose fittings and connec-

tions for air or oil leaks.

Low tractor hydraulic oil level.

Check tractor hydraulic oil level.

Loose or missing bolts or fasteners.

Check all bolts and fasteners.

Needle valve plugged.

Open needle valve, cycle markers

slowly and reset needle valve, refer to

page 42.

Needle valve(s) in sequence valve

plugged.

Open needle valves, cycle markers

slowly and reset needle valves, refer

to page 42.

Marker disk does not mark

Marker folding linkage does not have

enough slack to allow marker disk to

drop into field depressions.

Maximum down float should be lim-

ited by the slot at the rod end of the

marker cylinder, refer to page 43.

Reverse marker disk to pull or throw

dirt.

Trash build up on harrow

Level harrow or flatten tines.

Harrow stirring out seed

Adjusted too steep

Level harrow.

Chain

Debris in retainer clip

Be sure retainer clip is facing opposite

way of chain travel

Problem

Cause

Solution

Содержание 1510P



















































































































































Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510P, Руководство оператора

Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды