manualshive.com logo in svg

GREAT PLAINS 1510P, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510P Скачать руководство пользователя страница 92

Great Plains

 | 118-732M | 4/4/19

Table of Contents

Index

88

1510P & 1520P

Table of Contents

Index

Veris Drive Operating Instructions

Prior to Field Operational Use

Once the calibration procedures previously detailed been
followed, Console will store the calibration and rate
information until new information has been entered. 

1.

Turn on Console by pressing ON/VR key. 

Green light above ON/VR key will illuminate when

power is on. 

If the ON/VR key is pressed twice the unit will be put in VR

(Variable Rate) mode. Leave Console in manual mode. 

NOTE: For units with P/N 21567 skip step 3.

2.

To double-check calibration before planting, follow
same procedure as for mechanical ground drives
as outlined in Great Plains Precision Seeding
System Operator’s Manual, with these difference:

•

Volumetric: use extreme caution when
performing this calibration to prevent injury due
to drive entanglement. Also, turn drive gauge
wheel with a consistent speed of at least 30
rpm for maximum calibration accuracy. 

•

Singulated: Rather than calibrating from a
standing start, measure the distance as listed
in the GP manual, and set two flags. Start
driving far enough in advance of the first flag
that your unit is operating at field speed
(minimum 3 mph) during the calibration
distance.

Field Operational Use

1.

Turn on Console by pressing ON/VR key.

Refer to Figure 104

Green light above ON/VR key will illuminate when

power is on. 

Pressing the ON/VR key twice will put the unit in VR

mode. VR will appear on the screen along with the

Rate that is being sent from the computer. Press ON/

VR key again to toggle back to manual mode. (Mode

and rate changes take effect with the release of the

key).

To change rates manually whether in manual or in VR

mode, simply touch the Up/Down arrow keys. This will

change the Controller to the rate you select manually.

To return to VR, simply touch the ON/VR key to toggle

back to VR mode. 

2.

Engage the hydraulic flow by pushing FORWARD on
the tractor remote hydraulic lever. The remote lever
must be LOCKED OPEN in this position to provide
constant flow to the drive motor.

Figure 104

Main Operating Screen, in VR Mode

Содержание 1510P



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды