GREAT PLAINS 1510P Скачать руководство пользователя страница 52

Страница: 52 / 146

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

1510P & 1520P

Table of Contents

Index

Adjustments

Seed-Lok

Lock Up

Optional Seed-Lok

firming wheels provide additional

seed-to-soil contact. The wheels are spring loaded and
do not require adjusting. In some wet and sticky
conditions the wheels may accumulate soil.

Refer to Figure 55



NOTE: Side gauge wheel and seed meter is

removed for clarity.

To lock up Seed-Lok

wheels, raise drill. Rotate lock-up

handle (1) 90 degrees down on top of opener body, see
insert. Push up on Seed-Lok

wheel (2) until wheel arm

latches up.

Opener disk blades may be sharp. Use caution when making

adjustments in this area.

To unlock Seed-Lok

wheels, pull up lock-up handle

(1). Seed-Lok

is spring loaded so it will snap back into

place.

Harrow Adjustment

Harrow Frame Tube

Refer to Figure 56

This is one harrow setting that has been successful in
no- and minimum-till conditions. Because of different
soil moisture, trash levels and trash types, you may
need to reposition the tube frame or tines.

Figure 55

Seed-Lok Lock Up

18282

Push Seed-Lok
up to lock.

Locked
Position.

Unlocked
Position.

Figure 56

Spring Tine Angles

11891

Содержание 1510P



















































































































































Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510P, Руководство оператора

Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды