manualshive.com logo in svg

GREAT PLAINS 1510P, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510P Скачать руководство пользователя страница 16

Great Plains

 | 118-732M | 4/4/19

Table of Contents

Index

12

1510P & 1520P

Table of Contents

Index

Introduction

Introduction

Great Plains welcomes you to its growing family of new
product owners. This Drill has been designed with care
and built by skilled workers using quality materials.
Proper setup, maintenance, and safe operating practices
will help you get years of satisfactory use from the
machine.

Description of Unit

The 1510P and 1520P model drills are 3-point mounted
precision seeding systems equipped with either 10
Series or side-depth-control, 20 Series openers. The
openers are staggered for easy residue flow. Opener
depth can be adjusted.

Intended Usage

Use the drill to seed production-agriculture crops only. Do
not modify the drill for use with attachments other than
Great Plains options and accessories specified for use
with the drill.

Models Covered

This manual applies to Great Plains 1510P and 1520P
drills.

Document Family

118-732M

Operator Manual (this document)

118-732P

1510P and 1520P Parts Manual

151-144B

Seed Rate Manual

18326

Содержание 1510P



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды