GREAT PLAINS 1510P Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 146

background image

1510P & 1520P

Table of Contents

Operating Instructions

Great Plains

| 118-732M | 4/4/19

Table of Contents

23

Opener Operation

Do not back up with openers in the ground. To do so will cause

severe damage and opener plugging.

For information on opener adjustments, refer to page 41.
For more information on troubleshooting opener
problems, see “Troubleshooting”, page 50.

Marker Operation

Optional marker attachments are available from your
Great Plains dealer. Before operating markers, make
sure hydraulics are properly bled as described under
“Marker Adjustments”, page 41.

Dual markers equipped with a sequence valve are
powered off the same hydraulic circuit. Starting with both
markers folded, the folding sequence is:

1.

Activate lever - Right unfolds; left stays folded.

2.

Reverse lever - Right folds; left stays folded.

3.

Activate lever - Left unfolds; right stays folded.

4.

Reverse lever - Left folds up; right stays folded.

5.

Sequence repeats.

You can adjust marker folding speed. Refer to “Marker
Adjustments”, page 41, and adjust folding speed to a safe
rate. Folding markers at high speed can damage
markers.

«
...
25
26
27
28
29
...
»

Содержание 1510P



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1510P

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: Panasonic Страницы: 174

Бренд: Baker Страницы: 82

Бренд: XM Fitness Страницы: 10

Бренд: Landoll Страницы: 70

Бренд: Landice Страницы: 19

Бренд: Landice Страницы: 7

ST60+ SPEED INSTRUMENT

Бренд: Raymarine Страницы: 60

Бренд: Raymarine Страницы: 15

Бренд: RaycoWylie Страницы: 9

Бренд: Raven Страницы: 58

Бренд: Raven Страницы: 26

Бренд: Ravo Страницы: 114

Бренд: Alcoscan Страницы: 6

Бренд: Mach Страницы: 12

Бренд: ABB Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды