manualshive.com logo in svg

GREAT PLAINS 1510P, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510P Скачать руководство пользователя страница 9

1510P & 1520P

Table of Contents

Index

Important Safety Information

Great Plains

 | 118-732M | 4/4/19

Table of Contents

Index

5

Use A Safety Chain

Use a safety chain to help control drawn machinery

should it separate from tractor drawbar.

Use a chain with a strength rating equal to or greater than

the gross weight of towed machinery.

Attach chain to tractor drawbar support or other specified
anchor location. Allow only enough slack in chain to

permit turning.

Replace chain if any links or end fittings are broken,

stretched or damaged.

Do not use safety chain for towing.

Tire Safety

Tire changing can be dangerous and should be
performed by trained personnel using correct tools and
equipment.

When inflating tires, use a clip-on chuck and extension

hose long enough for  you to stand to one side–not in front

of or over tire assembly. Use a safety cage if available.

When removing and installing wheels, use wheel-handling
equipment adequate for weight involved.

Содержание 1510P



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды