GREAT PLAINS 1510P Скачать руководство пользователя страница 38

Страница: 38 / 146

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

1510P & 1520P

Table of Contents

Index

Adjustments

Cleaning Out Meters



NOTE: Shut off sliding seed tubes before attempting

to clean out seed meters.

Refer to Figure 34

For seed meter clean out:

Position tarp or buckets under the opener(s) whose
meter(s) you will be cleaning out.

Remove retaining clip and pull pin.

Refer to Figure 35

Pull up on meter clean out door to open.

Refer to Figure 36

When meter is empty, push meter clean out door
back to its original position to close.



NOTE: You may need to shake the clean out door a

little before closing to make sure all seeds fall out.

Replace pin and retaining clip

Figure 34

Meter Clean Out

18261

Retaining Clip

Clean Out Door

19190

Clean Out Door

Figure 35

Meter Clean Out Door

18293

Clean Out Door

Figure 36

Replacing Pin

Содержание 1510P



















































































































































Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510P, Руководство оператора

Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды