manualshive.com logo in svg

GREAT PLAINS 1510P, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510P Скачать руководство пользователя страница 46

Great Plains

 | 118-732M | 4/4/19

Table of Contents

Index

42

1510P & 1520P

Table of Contents

Index

Adjustments

Folding Speed with Needle Valves

Refer to Figure 46

A needle valve controls the folding speed of markers
that are plumbed separately. The needle valve is near
the rod end of the marker cylinder.

With tractor idling at a normal operating speed, adjust
marker folding to a safe speed. Turn adjustment knob
clockwise to reduce folding speed or counterclockwise
to increase folding speed. Excessive folding speed
could damage markers and void the warranty.

Refer to Figure 47

Folding Speed with Sequence Valve 

If markers are tied together with an optional sequence
valve, adjust folding speed with hex adjustment screws
on the sequence-valve body. There is one adjustment
screw for raising speed (1) and one for lowering speed
(2). Identify adjustment screws by markings stamped in
valve body.

With tractor idling at a normal operating speed, adjust
marker folding to a safe speed. Turn adjustment screws
clockwise to decrease folding speed and
counterclockwise to increase folding speed. Excessive
folding speed could damage markers and void the
warranty.

After adjusting the folding speed, tighten jam nuts on
hex adjustment screws to hold settings.

Figure 46 

Needle Valve

17620

Figure 47 

Speed Adjustment, Sequence Valve

14048

Hex Adjustment
Screws

Increase
Speed

Decrease
Speed

Содержание 1510P



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды