manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 6

www.glp.de

 

 

 

6 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

•

 

Respect all warnings and directions given in the user documentation and on KNV 
Dot and Line products. Read the user documentation and familiarize yourself with 
the safety precautions it contains before installing or using the products. GLP and 
affiliated companies will take no responsibility for damage or injury resulting from 

disregard for the information in the user documentation. 

•

 

Check the GLP website at www.glp.de and make sure that you have the latest 
version of this manual. Check the PSU software version indicated on page 2 of this 
manual and then check the version displayed in the KNV PSU’s control panel. If the 
versions are not the same, this manual may still cover your KNV installation because 

software updates do not always affect the way you use the elements in the system. 
However, it is possible that this manual does not match the system perfectly. 
Software release notes can help clarify this question. You can consult software 
release notes and download the correct version of this manual on the GLP website if 

necessary. 

•

 

Make all user documentation – this Quick Start and Safety Manual as well as the 
User Manual – available to all installers and operators. Save both documents for 
future reference. 

•

 

If you have any questions about the safe operation of KNV Dot and Line products, 

please contact an authorized GLP distributor (see list of distributors at www.glp.de). 

•

 

Use KNV Dot and Line products only as directed in this manual. Observe all markings 
in this manual and on the products. 

•

 

Refer all repairs and any service operation not described in this manual to a 

technician authorized by GLP. 

•

 

The light source in KNV Dot and Line fixtures must not be changed by the end user. 

•

 

Read and follow the user documentation for all additional equipment. 

 

 

Electrical safety 

•

 

Do not allow the fixture or PSU to become immersed. Do not expose the fixture or 
PSU to high-pressure water projections. 

•

 

Keep all unused connectors on the fixture and PSU sealed with their protective caps 
at all times, both when they are in use and when not in use. 

•

 

Use only a source of AC mains power that complies with local building and 
electrical codes and has both overload and ground fault (earth fault) protection. 

•

 

Ensure that the fixture is electrically connected to ground (earth). 

•

 

Disconnect the system from AC mains power before carrying out any installation or 
maintenance work and when the system is not in use. 

•

 

Disconnect the PSU from power immediately if any seal, cover, cable, connector or 
other component is damaged, defective, deformed or showing signs of 

overheating. Do not reapply power until the item has been repaired and the 
installation judged to be safe by a technician authorized by GLP. 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды