manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 33

German Light Products® 

 

 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

33 

9.

 

KNV Line installation 

KNV Line installation options 

A KNV Line may be installed as follows: 

 

Fastened into an adjustable KNV Floorstand / Hanging Bracket and standing on a 
stable horizontal surface. 

 

Fastened into an adjustable KNV Floorstand / Hanging Bracket that is fastened to a 
rigging truss at any angle using a rigging clamp or fastened to a surface or 

structure. 

 

Fastened into a non-adjustable KNV Installation Bracket that is fastened to a rigging 
truss or similar structure at any angle using a rigging clamp. 

 

Fastened to other KNV Lines vertically and horizontally with KNV Module 
Connectors to form an array that is: 

•

 

maximum ten (10) fixtures tall if every column in the array is independently 
suspended from a rigging truss, or 

•

 

maximum five (5) fixtures tall wherever a column inside the array is supported by 

the fixtures on both sides of it instead of being independently suspended from a 
rigging truss. 

 

Supported on both sides by two KNV fixtures that are fastened to it using KNV 
Module Connectors. Each of the two outer fixtures must be fastened to a rigging 
truss or other structure at any angle using a half-coupler rigging clamp. 

KNV Line and Cube pixel layout 

Five KNV Line fixtures fastened to each other side-to-side have the same number of 
pixels with the same dimensions as one KNV Cube. 

Mechanical connectors on the KNV Line 

See Figure 18. Channels (arrowed) for mechanical connectors are provided on the 

top, bottom, left and right-hand sides of KNV Lines. These channels accept KNV 
Module Connectors, the fasteners on KNV Installation Brackets and the fasteners on 
KNV Floorstand / Hanging Brackets. The channels incorporate catches that work 
together with the two different types of locking mechanism found on KNV installation 
hardware. 
 
 
 

 
 

 
 

Figure 18. Mechanical connector channels on KNV Line 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды