manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 5

German Light Products® 

 

 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

5 

1.

 

Safety 

Key to symbols 

The following symbols are used in this Guide: 

 
 

 

General safety information 

Read this manual carefully before installing, using or servicing the KNV Dot, KNV Line or 
KNV PSU.  

If you have any doubts or questions about how to use the fixture or PSU safely, please 
contact your GLP® supplier who will be happy to help. 
The user documentation for KNV Dot and KNV Line lighting fixtures and the KNV PSU 
consists of: 

•

 

The 

KNV Dot and Line Quick Start and Safety Manual

, supplied with fixtures and with 

the PSU, and available for download from www.glp.de. The Quick Start and Safety 

Manual contains important safety information and installation instructions that the 
installer and user must read. 

•

 

The 

KNV Dot and Line User Manual

, available for download from www.glp.de. The 

User Manual explains features and control of these fixtures. 

•

 

The 

KNV Dot DMX Channel Index

 and 

KNV Line DMX Channel Index

, available for 

download from www.glp.de. The Channel Indexes are separate guides to the DMX 
control channel layouts and DMX commands available in these fixtures.  

All documents are available for download from www.glp.de.  
KNV Dot and Line fixtures are intended for use by experienced professionals with the 

knowledge and skills to set up, operate, and maintain high-powered, remotely 
controlled lighting equipment safely and efficiently. These operations require expertise 
that may not be provided in the user documentation. 

 

Warning! 

Safety hazard. 

Risk of severe injury or 
death.

 

 

Warning! 

Hazardous voltage. 

Risk of lethal or severe 
electric shock.

 

 

Warning! 

See user 

manual for important 
safety information.

 

 

Warning!

 Fire hazard. 

 

Warning!

 Risk of eye 

injury. 

 

 

 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды