manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 52

www.glp.de

 

 

 

52 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

13.

 

Starting and stopping operation 

Warning!

 Before you apply power to the KNV installation or operate it after a 

blackout, make sure that nobody is looking directly into the front of the 
fixtures. 

 
The KNV PSU’s TRUE1 AC mains power input connector supports hot-plugging, and it 
can be quickest to disconnect a live power cable if you need to shut down power 
urgently, but it is still good practice to shut down power to the AC mains power circuit 
before connecting and disconnecting power cables.  
To start operation, check that nobody is looking into the front of any connected 
fixtures, then apply power to the AC mains power circuit. 
To stop operation, shut down power to the AC mains power circuit. 

Transportation and storage 

We strongly recommend that you transport KNV fixtures and PSUs either in flightcases or 
in their original packaging to protect them from damage during transportation. The 
product warranty does not cover damage caused by abnormal shocks during 
transportation and handling. 
When KNV products are not being used, disconnect them from power and store them 

in a dry location. 

 

 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды