GLP KNV Dot Скачать руководство пользователя страница 32

Страница: 32 / 65

www.glp.de

KNV Dot and Line Quick Start and Safety Manual Rev. A

KNV Dot arrays containing single Dots between columns

Warning!

Any KNV Dot that is not part of an independently supported column must
be fastened on both sides to KNV Dots that are in independently supported

columns: do not create an installation where any KNV Dot is supported on
only one side.

See Figure 17. You can create
an array of KNV Dots with
single Dots installed between
full columns of Dots, but you
must observe the following

precautions:

•

Use the instructions given in
the section ‘Array where at
least every second column

is supported’ starting on
page 30 as a guide.

•

Make sure that the columns
on the left- and right-hand
edges of the array and

every second column inside
the array are complete,
unbroken columns of Dots
and that they are correctly

supported using rigging
clamps.

•

Respect the maximum limit
of five Dots vertically.

•

Make sure that any single

Dot that is installed
between full columns is
fastened to Dots on both
sides using GLP Slide

Connectors.

Figure 17. KNV Dot array with single

Dots between full columns

Every column

at edge

of array

supported and

with no gaps

Every second

column

independently

supported and

with no gaps

Every column

at edge

of array

supported and

with no gaps

Содержание KNV Dot


































































Результаты поиска

Содержание KNV Dot

Отзывы:

Бренды по названию

Популярные бренды

GLP KNV Dot, Быстрый старт и руководство по безопасности

Результаты поиска

Содержание KNV Dot

Отзывы:

Бренды по названию

Популярные бренды