manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 35

German Light Products® 

 

 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

35 

 

Locks on KNV Line brackets 

KNV Line Floorstands, Installation Brackets 
and Line Brackets incorporate a spring-

loaded locking mechanism: 

•

 

See Figure 19. Push both locking knobs 
in, towards the fixture, to lock. 

•

 

Push the locking knobs out, away from 
the fixture, to unlock. 

 
 

Locks on KNV Line mechanical connectors 

KNV Line Module Connectors and Rigging Connectors incorporate a locking 

mechanism: 

•

 

To lock a connector, see Figure 20. Push the connector into the channels in fixtures 
and twist the connector knob 90° clockwise to lock. 

•

 

To release a connector, press the connector knob, twist 90° counterclockwise, and 
pull the connector out of the channels. 

 

Figure 19. Locking mechanism on  
KNV Line Floorstand and Brackets

Figure 20. Locking mechanism on KNV Line mechanical connectors 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды