manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 22

www.glp.de

 

 

 

22 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

 

GLP 5/8'' (16mm) Installation Spigot incl. screw 

Mounts on Rigging Clamp 13-55/45/15 or GLP Slide 
connector. 

 

GLP Slide Connector 

Slides and locks into two KNV Dots to allow the Dots to be 

fastened together with a 1:2 pixel pitch compared to KNV 
Line and KNV Cube fixtures.  

 

GLP Half-Slide Connector and 5/8” (16 mm) Installation 
Spigot assembly 

Slides and locks into a KNV Dot to allow the Dot to be 
suspended from a Rigging Clamp 13-55/45/15.  

 
 

Fastening KNV Dots together 

See Figure 9. Channels 

(arrowed) are provided on the 
top, bottom, left and right sides 
of KNV Dots. These channels 
accept GLP Slide Connectors 
and the fasteners on KNV Dot 

Brackets. Each Slide Connector 
incorporates a safety 
mechanism that allows the 
connector to be locked into 

the channel. 
 
To fasten two KNV Dots to 
each other: 

 

Line up the Dots next to 
each other. 

 

See Figure 10. Push down on the locking button 

A

 on a GLP Slide Connector and 

slide the connector into the connector channels 

B

 on both Dots as shown at 

C

. 

 

Release the locking button 

A

 so that the locking tab 

D

 engages in the cutouts in 

the connector channels of both Dots. Check that the GLP Slide Connector is 
locked into the channels and that the Dots are locked securely together. 
 

Figure 9. Channels for Slide Connectors in KNV Dot 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды