GLP KNV Dot Скачать руководство пользователя страница 3

Страница: 3 / 65

Table of Contents

Safety ................................................................................................. 5

Key to symbols .............................................................................. 5

General safety information ......................................................... 5

Electrical safety ............................................................................ 6

Fire safety and protection from burns........................................ 7

Eye safety ...................................................................................... 8

Strobe safety ................................................................................. 9

Installation safety and protection from personal injury ........... 9

Avoiding damage .......................................................................... 11

General precautions ................................................................. 11

Avoiding damage from light sources ...................................... 11

IP rating ....................................................................................... 12

Avoiding damage from water and humidity .......................... 12

Avoiding damage from dust and airborne particles ............. 13

Transportation and storage ...................................................... 13

KNV Dot overview ........................................................................... 14

KNV Line overview .......................................................................... 15

KNV PSU overview ........................................................................... 16

Features ........................................................................................... 18

Control and functions ................................................................ 18

Installation: general ........................................................................ 19

Pixel mapping ............................................................................. 19

Securing with a safety cable .................................................... 19

KNV Dot Installation ........................................................................ 21

KNV Dot installation options ...................................................... 21

KNV Dot Installation hardware ................................................. 21

Fastening KNV Dots together .................................................... 22

Flying a single KNV Dot using a KNV Dot Bracket ................... 23

Flying a single KNV Dot using a Half-Slide Connector ............ 24

Flying a column of KNV Dots using a KNV Dot Bracket .......... 25

Flying a column of KNV Dots using a Half-Slide Connector .. 26

Flying an array of KNV Dots using Half-Slide Connectors ...... 28

KNV Line installation ....................................................................... 33

KNV Line installation options ..................................................... 33

Содержание KNV Dot


































































Результаты поиска

Содержание KNV Dot

Отзывы:

Бренды по названию

Популярные бренды

GLP KNV Dot, Быстрый старт и руководство по безопасности

Результаты поиска

Содержание KNV Dot

Отзывы:

Бренды по названию

Популярные бренды