manualshive.com logo in svg

GLP KNV Dot, Быстрый старт и руководство по безопасности

Поделиться
Скачать
GLP KNV Dot Скачать руководство пользователя страница 34

www.glp.de

 

 

 

34 

KNV Dot and Line Quick Start and Safety Manual Rev. A 

KNV Line installation hardware 

The following items of installation hardware are available from GLP for the KNV Line. 
Use them only as directed in this manual. Respecting all warnings on the hardware and 

in this manual. If you use any other installation hardware than those items listed below, 
check with GLP or with the hardware supplier to make sure that you do not exceed 
safety limits. 
 

 

KNV Floorstand / Hanging Bracket 

Adjustable. 
May be used to stand one KNV Line or KNV Cube fixture 

on a stable horizontal surface. 
May be used to support one KNV Line or KNV Cube 
fixture hanging vertically from a rigging truss, bar or 
similar support. 

 

KNV Installation Bracket 

Non-adjustable.  
May be used to fasten a KNV Line, Cube or Arc to a 
supporting structure.  
May be used in combination with rigging clamps to 
provide the required points of support in larger and 
creative arrays of KNV Line, Cube and/or Arc fixtures. 

 

KNV Line Bracket 

Non-adjustable. 
May be used in combination with a rigging clamp to 
provide a point of support for a KNV Line fixture. Gives 
flexibility in creative arrays of KNV Line fixtures. 

 

KNV Module Connector 

May be used to lock two KNV Line, KNV Cube or KNV 
Arc fixtures to each other vertically and side-by-side. 
You can use this fastener to support the weight of 
fixtures if you respect the safety limits given in this 
manual. You can use it to align fixtures in all situations 

where the weight of the fixtures is correctly supported. 

 

KNV Rigging Connector 

Fastens to a KNV Line, Cube or Arc for use as a rigging 
clamp attachment bracket. 
May be used in combination with a rigging clamp to 

support a vertical column of up to twenty (20)

 

KNV Line 

fixtures.

 

Содержание KNV Dot


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды