GILES GBF-50 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 111

GILES GBF-50 Скачать руководство пользователя страница 77

67

Cleaning

GBF-50 Fryer

7. Reassemble filter pan using new/refreshed filter media

(a clean filter

screen or [1] new sheet of filter paper)

. Be sure that filter media is

properly installed underneath the

hold

‐

down frame

and that frame is

properly secured by the

(4) locking levers

.

8. Replace

cover

⑦

, position assembled filter pan under the unit and re

‐

connect

filter pan hose

⑧

at the filter pan coupling

(push in slip

‐

ring

while inserting hose fitting)

. The connection must be tight and secure for

proper operation.

7

Filter Media Note:

• A reusable Stainless Steel Filter Screen is standard for the GBF

‐

50 fryer

‐

wash a soiled screen in sink, using

ONLY

clean hot water and a stiff bristle brush ...

DO

NOT

use soaps or cleaners. Shake off excess water and blot dry

with clean paper wipes. Ideally, screen should be allowed to dry overnight before using.

•

Filter Paper

‐

remove soiled paper media and discard. Replace with one (1) fresh sheet of properly sized filter

paper.

Available through Giles dealers/distributors: P/N 65871

.

Stainless Steel Filter Screen

With proper use and care, this sustainable, reusable, filter screen should have a long service life. However, it
should be replaced if it becomes torn, punctured, frayed or if the silicone edge gasket becomes significantly
damaged.

When filtering oil, proper use of a suitable filter aid, such as

Giles Filter Powder

, is essential for proper filtering

and reconditioning of used cooking oil.

8

5.02

Cleaning the Filter Pan

&

Refreshing Filter Media - continued

«
...
75
76
77
78
79
...
»

Содержание GBF-50
















































































































Отзывы:

Нет отзывов