manualshive.com logo in svg

GILES GBF-50, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
GILES GBF-50 Скачать руководство пользователя страница 15

2.

Installation

2.01

Appliance Location

DO NOT MODIFY, ADD ATTACHMENTS OR OTHERWISE ALTER THIS EQUIPMENT

GBF Series Fryers

Installation

5

2.02

Unpacking

Fryer is shipped on a wooden pallet; secured with high

‐

tensile plastic strapping and enclosed by a wooden 

framework.  The entire unit is wrapped in plastic film stretch wrap.

 
 

 

•   To avoid possible damage, the appliance must remain in an upright position while uncrating. 

•   Exercise care when removing the wooden framework from the shipping pallet. 

•   A single unit is 

heavy ... banked units will be very heavy

.  Use extreme care and appropriate handling 

equipment and/or sufficient manpower when lifting or moving the equipment from pallet. 

•   Failure to comply with these 

CAUTION

 notices may result in minor or moderate injury, equipment or property 

damage, and void the factory warranty.

Continued on Next Page

The following sections explain procedures for properly installing and preparing the appliance for use.  To help avoid 
personal injury or damage to the equipment, please adhere to all recommended procedures. 

IMPORTANT!  All material and labor expenses required for installation are the sole responsibility of the customer.  
Generally, it is advisable to engage the services of professional commercial kitchen equipment specialists, a licensed 
electrician, and/or a qualified HVAC contractor to manage the specific details of the installation.  Please call Giles 
Technical Support @ 800.554.4537, if assistance is required.

1.        Appliance and surrounding area must be free and clear of combustible materials.  Maintain 3” [7.6 cm] 

clearance. 

2.        Provide adequate space to allow access for future servicing and proper operation. 

3.        Be sure that electrical service available in the intended location is a circuit adequate for powering the 

appliance load.  

NOTE:  

A banked system requires a separate electrical service for each fryer unit

.  

4.        Be certain the unit is installed in a stable position and will not unintentionally move.  Front casters have 

locking brakes ... be sure they are kept locked when in operation.  Some authorities may require that special 
anchoring be utilized for this type of appliance ... check local code.  The rear of the fryer cabinet has an eye

‐

bolt attached for this purpose.  

5.        The appliance must be installed, operated, and maintained in accordance with the 

Standard for Ventilation 

Control, and Fire Protection of Commercial Cooking Operations, NFPA 96

.  Ventilation must be provided to 

eliminate grease

‐

laden cooking vapors, as required by local code requirements. 

These steps will help to ensure proper installation.  If there are questions concerning these procedures, contact 

Giles 

Technical Support

 at 

800.554.4537

 or email 

[email protected]

. 

Содержание GBF-50
















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды