GILES GBF-50 Скачать руководство пользователя страница 19

Страница: 19 / 111

Installation

GBF-50 Fryer

2.07.1 Bulk Oil Management System Connections - Fresh & Waste Oil

•

Optional

factory

‐

installed fryer plumbing ready for connection to a

customer

‐

supplied Bulk Oil Management system

. Depending on which

option was specified, fittings on rear of unit can be directly connected to
either,

fresh oil supply system,

waste oil discharge system, or both.

The

ports are plugged if option(s) are not installed.

On a banked fryer system,

these connections service all fry vats

. When connecting fryer to such bulk

systems, closely follow installation guidelines of the

system’s

manufacturer

• When fresh oil supply system is connected, the system oil pump must be

wired into the

“ADD OIL”

pushbutton switch on the fryer control panel

(main unit of a banked system)

. Pressing and holding this button operates

the fresh oil system pump to fill vat, or top

‐

off oil level.

• When bulk waste oil collection system is connected, waste oil will be

pumped to it by the fryer’s on

‐

board filter pump. To prevent possible

pump damage, an internal pressure switch will stop pump operation in the
event of blockage, clog, or excessive back

‐

pressure.

• Use of

quick

‐

connect/disconnect couplings

is recommended to facilitate

moving the appliance for cleaning and service activities.

IMPORTANT!

All materials (pipe, fittings, electrical, etc.) and labor necessary for

connecting fryer to Bulk Oil System is provided by the customer and not
included with the purchase of these options.

2.07

Optional Factory-Installed Features

FRESH OIL

INLET

WASTE OIL

OUTLET

ADD OIL

PUMP

SWITCH

2.07.2 On-Board Fresh Oil Supply System

•

Optional

factory

‐

installed

‐

board system

uses a removable

”saddle

‐

bag

style”

storage tank, which hangs on fryer side and connects to the

fresh oil

inlet

via flexible hose

The amount of fresh oil supply in the tank must be

manually maintained by the user. When low oil level in the vat is indicated by
the controller, pressing & holding the

[ADD OIL]

push

‐

button switch on the

control panel pumps fresh oil from the tank to the cook vat ... switch must be
held for pump to operate ... hold until oil level is replenished.

On a banked fryer system, the single tank supplies all fry vats

• Connection to a bulk fresh oil supply system is the alternative to this on

‐

board

system option ... [ADD OIL] pushbutton will control bulk oil pump.

This option cannot be equipped when using the bulk fresh oil supply option.

Содержание GBF-50
















































































































Результаты поиска

Содержание GBF-50

Отзывы:

GILES GBF-50, Руководство по эксплуатации и обслуживанию, Страница: 19 / 111

Результаты поиска

Содержание GBF-50

Отзывы: