GILES GBF-50 Скачать руководство пользователя страница 107

Страница: 107 / 111

Appendix

GBF-50 Fryer

Appendix A: Connecting Optional KITCHENTRAC

™

If your new

Giles

cooking appliance is equipped with the

optional, factory

‐

installed,

KitchenTrac

™

Remote Monitoring

application, it is ready to be connected to the

Giles

KitchenTrac™

cloud server via your local

WiFi

network. The app

allows remote tracking of performance & productivity, menu
sales trends, maintenance events and a multitude of other
analytics pertaining to the connected appliance.

Each controller monitored by

KitchenTrac™

requires a small

monthly

server hosting fee

, but the benefits will pay for that many times over

On banked fryer systems, each

controller is considered separately

For an additional

monthly monitoring fee

(per controller),

Giles

can provide “around

‐

the

‐

clock”, online monitoring

(by our Support Team)

for your connected equipment, and provide direct notification of detected issues.

WiFi Connection Manual, Form #66313

was shipped with your new equipment, but the steps in this appendix also

describe the process for connecting a controller to

KitchenTrac

™. After new equipment is installed and checked

out, precisely follow these instructions to get connected and begin experiencing the benefits of remote monitoring.

Should you encounter difficulties with this process, please contact

GILES Technical Services @ 800.554.4537

[email protected]

for assistance.

Appendix A.1

Connecting WiFi Board to Wireless Router

IMPORTANT! There must be a consistent, open,

connection to the internet via a wireless WiFi

router, which is within range of the monitored

equipment. A password for the establishment’s

router may be required.

1. Set

Power Switch

①

[ON]

, allow controller to power

‐

up. Be sure to keep the

Heat Switch

②

in the

[OFF]

position throughout the process to prevent heating elements from energizing.

2. Press

[TIME]

③

+ 9 4 3 4

on keypad,

then press

[START]

key

④

Message

“WiFi Setup PRESS [START]”

appears on the

upper controller display

⑤

... press

[START]

key.

“SEARCHING FOR WIFI MODULE”

appears on display.

WiFi

module is not detected within

10 seconds

, message

“COMMUNICATIONS ERROR, CHECK CONNECTIONS”

is displayed. Indicates that

WiFi

board is not detected by the controller. Several issues can cause this error ...

DIP switches are not set properly, cable is disconnected, jumpers are missing, etc.
Turn power switch

[OFF]

, check switches, jumpers and connections, then retry. If the error persist, call

Giles

Technical Services @ 800.554.4537

for assistance.

4. If module is detected, message

“WIFI MODULE FOUND, CONFIGURING”

appears.

Continued on Next Page

Содержание GBF-50
















































































































Результаты поиска

Содержание GBF-50

Отзывы:

Бренды по названию

Популярные бренды

GILES GBF-50, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GBF-50

Отзывы:

Бренды по названию

Популярные бренды