GILES GBF-50 страница 71 Скачать руководство пользователя

Страница: 71 / 111

Fryer Operation

GBF-50 Fryer

NOTE: The pump system is equipped with a pressure sensor. Should piping become clogged, or the
collection tank is full, excessive back

‐

pressure is detected and the pump will shutdown to prevent possible

damage. Should this occur, cease pump operation and have maintenance personnel inspect the system.

4.05 Removal of Waste Cooking Oil from Fryer - continued

1. Allow filter pan to sufficiently cool, then remove from fryer, disassemble and clean thoroughly. Refer to

Section

5.03

2. After waste oil has been removed, a

Boil

‐

Out Procedure

should be performed promptly. See

Section 5.01, Boil

‐

Out Procedure

. It is recommended

NOT

to allow oil residue to remain in the vat for an extended period of time

... it will dry out, become difficult to clean, and can cause a build

‐

up which can negatively impact fryer

performance and food quality.

If postponing

boil

‐

out

is unavoidable, at a minimum, use absorbent paper wipes to clean as much waste oil

residue, as possible, from the vat & heating elements. Clean the

filter pan

and refill pot with fresh oil. Restart

fryer as described in

Section 4.02, Cooking Procedures

To perform a Boil

‐

Out on the unit, see

Section 5.01, Boil

‐

Out Procedure

To shut down unit, see

Section 4.06, Normal Shut

‐

Down

Completing the Oil Removal/Disposal Process:

4.06 Fryer Shut-Down

1. Place

Heat Switch(es)

①

[OFF]

2. Place

Power Switch(es)

②

[OFF]

position.

3. Verify that the

Oil Return Valve(s)

③

is in the

[CLOSE]

position

(all units of banked system)

. Failure to do this

can allow oil to siphon back from vat to the filter pan.
On a

banked systems

this could result in overflow of the

filter pan overnight, and also create a

low oil fire hazard

at start

‐

up the

next day.

All units of a banked system require separate shutdown.

Emergency Shut

‐

Down:

In case of emergency, disconnect supply power from the appliance at the
building’s main electrical panel, and/or follow all standard emergency
procedures prescribed by your specific

Standard Operating Procedures

Содержание GBF-50
















































































































Результаты поиска

Содержание GBF-50

Отзывы:

Похожие инструкции для GBF-50

Бренды по названию

Популярные бренды

GILES GBF-50, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GBF-50

Отзывы:

Похожие инструкции для GBF-50

Бренды по названию

Популярные бренды