Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 26

Страница: 26 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Staff Gauge

Setting the sensor height relative to the measurement is done using staff gauge. The sensor will output

relative measurement of the actual water level based on its height above the riverbed.

Power management

Switching the device between continuous scanning mode and SDI-12 sleep modes. In continuous mode

the device constantly makes the measurements, which are transmitted over RS-232 interface and made

available over Modbus and SDI-12 interfaces. The device is always available over RS-232 and Modbus

interfaces. In any SDI12 sleep mode, the device remains in the sleep mode until SDI-12 Measure (aM!)

command is received. While in deep sleep mode, the device will not be able to connect to Modbus or

RS-232 interface. For reconfiguring the device which is set to operate in SDI-12 deep sleep mode, it’s

necessary to power-cycle the device, and then use this application to connect to the device within 20

seconds after power-up. If there is no attempt to connect to the device over RS-232 within 20 seconds,

the device will automatically go back to sleep mode. The device consumes only 0.08W while in standby

mode, and 0.04 W while in sleep mode.

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды