Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 18

Страница: 18 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Warm Up Time

Warm up time

- The time after sensor power-up, during which all measurements are ignored. This time

is used to settle auto-gain parameters, Kalman filter values, averaging filter, and all other operational

parameters. It is recommended to set this value to a minimum of 5 seconds. In extreme cases where

a quick response after unit power-up is required, 3 seconds can be used, with a possibility of losing

measurement accuracy.

4 – 20 mA output

4 – 20

mA output

- This parameter is used to select the value that will correspond to the 4 – 20 mA

output. When

Velocity

is selected, the output current will be proportional to the measured velocity. When

Level

is selected, the output current will be proportional to the measured level and when

Discharge

selected, the output current will be proportional to the calculated discharge. When

None

is selected, the

4 – 20 mA output will be disabled.

4 – 20 mA min. and 4 – 20 mA max.

4 – 20 mA min.

– To configure the 4 – 20 mA output range, the minimum measured value which

will correspond to 4 mA analog output needs to be set. The value is set in the currently configured

measurement unit. Example: if values measured by the instrument are expected to be within the range

of 700 mm/s up to 1500 mm/s, it is recommended to configure the minimum value to slightly below 700

mm/s (for example 500 mm/s). Alternatively, if the resolution is not critical, then the minimum value for

4 – 20 mA output can be left to the instrument minimum of 0 mm/s.

4 – 20 mA max.

– To configure the 4 – 20 mA output range, the maximum measured value which

will correspond to 20 mA analog output needs to be set. The value is set in the currently configured

measurement unit. Example: if values measured by the instrument are expected to be within the range

of 700 mm/s up to 1500 mm/s, it is recommended to configure the maximum value to slightly above

1500 mm/s (for example 2000 mm/s). Alternatively, if the resolution is not critical, then the maximum

value for 4 – 20 mA output can be left to the instrument maximum of 15000 mm/s.

WARM UP TIME

POWER ON

Dead time

Output value 4-20 mA

20 mA

4 mA

Min. Value

Max. Value

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды