Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 49

Страница: 49 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Name

Command

Response

Details

Get Level Filter

Type

aXGLFT!

a+d<CR><LF>

+d – filter type for level

0 – no filter, 1 – IIR filter, 2 –

Moving average, 3 – Median, 4 –

Standard deviation

Set Level Filter Type d!

a+d<CR><LF>

+d – filter type for level

0 – no filter, 1 – IIR filter, 2 –

Moving average, 3 – Median, 4 –

Standard deviation

Get Peak Detector

Type For Level

aXGPDT!

a+d<CR><LF>

+d – identifies the peak detector

type, can be any of the following:

0 – report the distance to the

maximum peak which corresponds

to the maximum radar signal

reflection

1 - report the last peak which

corresponds to the furthest

reflection from the radar; this

may include multipath reflections

in typical cases and should be

avoided

Set Peak Detector

Type For Level

a+d<CR><LF>

+d – identifies the peak detector

type, can be any of the following:

0 – report the distance to the

maximum peak which corresponds

to the maximum radar signal

reflection

1 - report the last peak which

corresponds to the furthest

reflection from the radar; this

may include multipath reflections

in typical cases and should be

avoided

Device supports all other commands required by SDI-12 v1.3 and will respond to them but all relevant

data can be acquired using the commands from the table above.

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды