Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 6

Страница: 6 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Cable Pin-Out

The flow meter is supplied with open end cable consisting of 12 wires coded with colours. Table 2

gives a detailed description for each wire.

It is possible to mount optional connectors on the cable end per user request. In this case, the

connector specification and connection diagram must be specified when ordering the sensor.

Table 2. Cable Pin-Out

Pin No.

Wire Color

Pin Name

Pin Description

White

GND

This pin should be connected to the ground (neg

ative) pole of the power supply.

Brown

+Vin

The power supply for the Radar Speed Sensor is

provided on this pin. The Radar Speed Sensor pow

er supply voltage must be in the range 9 VDC to 27

VDC, and the power supply must be able to provide

at last 0.65W

Green

RS232 – TxD

RS-232 data transmit signal.

Yellow

RS232 – RxD

RS-232 data receive signal.

Grey

GND

Signal ground.

Pink

CAN – H

CAN2.0B high signal. (optional)

Blue

CAN – L

CAN2.0B low signal. (optional)

Red

SDI12 DATA

SDI12 data line

Orange

RS485 – D-

RS-485 data transmitter/receiver low signal.

Dark Red

RS485 – D+

RS-485 data transmitter/receiver high signal.

Black

Alarm SW or 4–20 mA

Secondary (Optional)

Alarm 1 - open collector switch signal max.

60mA

Purple

4 – 20 mA

Sink for 4 – 20 mA analog interface. Connect

sensing device as pull-up to sink the current

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды