Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 24

Страница: 24 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Measurement Parameters

Discharge unit

– The measurement unit used to report the measured discharge value.

Velocity unit

– The measurement unit used to report the measured velocity value. For NMEA protocol

which is used over RS-232 connection, the velocity is reported as an integer value. To preserve higher

precision with integer numbers, the measured velocity will be multiplied by 10 for m/s, km/h, mph, fps

and fpm when being transferred over RS-232. When mm/s and cm/s units are used, the measured

values will not be multiplied by 10. The Geolux Instrument Configurator PC application internally handles

the multiplication factor which is used over RS-232 protocol, and it displays the correct values to the

user.

Level unit

– The measurement unit used to report the measured level value. The default measurement

unit is millimetres. When changing the measurement unit, it’s important to make sure that other

parameters which depend on the measurement unit (such as active zone parameters) are also changed

to the new unit.

PGA sensitivity

– This parameter limits the maximum gain (amplification level) of the internal

programable gain amplifier. It is strongly recommended to use the default value 8, which allows the

internal signal amplifier to use the maximum gain when the reflected radar signal is very low. Setting

this value to a lower value is used only when the instrument is mounted very close to the water surface,

typically less than 1 metre, and in that case this parameter should be set to a value of 4 or 5.

Velocity min. and Velocity max.

Velocity min.

- This parameter is used for setting up the minimum velocity value of interest.

Velocity max.

- This parameter is used for setting up the maximum velocity value of interest.

Gain

PGA

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды