Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 65

Страница: 65 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

5. Check that the device is not operating in low power

The instrument can be configured to operate in low power mode. While in

low power mode, the instrument will not make any measurements but it’s

communication interfaces will be active. To check whether the instrument is

operating in low power mode, check Power management parameter which is

available under... and make sure that Continuous scanning is selected.

6. Make sure that the COM port is not already open

Only one application may use a single COM port in the system. Make sure that no

other open application uses the same COM port that you are trying to open.

7. Try restarting the application and/or the computer

Close and reopen the configurator application and try to establish the connection

again.

Restart your computer and try to establish the connection to the instrument again.

The instrument

does not respond

over Modbus (RS-

485) interface.

1. Make sure that the cable is properly connected to the instrument

Check that the cable M12 circular connector is firmly connected and screwed to the

instrument. It is not sufficient to simply attach the cable connector to the instru

ment connector, the cable connector must be screwed into the instrument connec

tor.

2. Check power supply

Make sure that the power is being supplied to the instrument. A direct-current volt

age, between 9 and 27 Volts must be connected to brown (+) and white (-) wires of

the instrument cable. The power supply must be able to deliver at least 500 mA of

current.

3. Check RS-485 connector

Make sure that the RS-485 lines on the instrument cable are properly connected to

the RS-485 connector. The dark red wire should be connected to D+ line, and the

orange line should be connected to D- line.

Make sure that the D+ and D- lines are not swapped.

Make sure that you have correctly identified and connected the dark red (magenta)

wire, as there is also another bright red wire that is used to provide output power

for 4-20 mA output. It is possible to misidentify the wire and to connect the bright

red wire to D+ instead of dark red wire.

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды