Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 17

Страница: 17 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Device ID

- Configures the device (slave) ID to be used on RS-485 interface protocols (Modbus RTU

or HS). Both protocols use request/response format and allow multiple instruments to be connected

on the same bus. When a remote master transmits the request message, it will use the device ID as

a device address. All instruments will receive the request, but only the instrument with the matching

device ID will answer to the received request.

Modbus settings

- Configures the parity and number of stop bits used in communication. Parity is

used in serial communication for basic error detection. When parity is set to

None

, no parity is used,

and no error detection is possible on bit level. When parity is set to

Odd parity

, an additional bit is

added to the communication that will be set to 1 when there is an odd number of bits with value

1 in the 8-bit payload byte. Similarly, when parity is set to

Even parity

, an additional bit is added

to the communication that will be set to 1 when there is an even number of bits with value 1 in the

8-bit payload byte. Generally, all bytes on the receiver side where the parity bit is not matching the

message will be discarded. The default setting on most devices that use Modbus is even parity. Stop

bits are added to the end of each data byte transferred over serial communication, to allow pause

between two bytes. One or two bits may be used. The default setting is even parity and one stop bit.

ID+1

Device ID

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды