Geolux GLX-RSS-2-300 WL Скачать руководство пользователя страница 30

Страница: 30 / 71

GLX-RSS-2-300 WL User Manual

GLX-RSS-2-300 WL Non-Contact Flow Meter

Water level report

$LVL,L1,L2,T1,L3,L4,S1,S2*CSUM<CR><LF>

$LVL:

The keyword sent in the beginning of each level report.

L1:

Current distance from sensor to water, in defined units, 0 being sensor

reference plane. If reporting -4 then there is no detected level.

L2:

Average distance from sensor to water, in defined units, 0 being sensor

reference plane. If reporting -4 then there is no detected level.

T1:

Internal device temperature (in °C).

L3:

Current relative detected level, in defined units, 0 being sensor reference

plane.

L4:

Average relative detected level, in defined units, 0 being sensor reference

plane.

S1:

Measurement SNR (in dBm).

S2:

The standard deviation of water level measurements. The number of

samples used to calculate the standard deviation is equal to the configured

filter length.

CSUM:

The check sum of the characters in the report from $ to * excluding these

characters.

Level sensor tilt angle report

$LVLANG,A1,A2 *CSUM<CR><LF>

$LVLANG:

The keyword sent in the beginning of each level sensor tilt angle report.

A1:

The tilt angle of the instrument along X axis. For proper operation of the

instrument, ensure that this angle is zero, or as close to zero as possible

(between -1 and +1 degrees).

A2:

The tilt angle of the instrument along Y axis. For proper operation of the

instrument ensure that this angle is zero, or as close to zero as possible

(betwee n -1 and +1 degrees).

CSUM:

The check sum of the characters in the report from $ to * excluding these

characters.

Содержание GLX-RSS-2-300 WL







































































Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды

Geolux GLX-RSS-2-300 WL, Руководство пользователя

Результаты поиска

Содержание GLX-RSS-2-300 WL

Отзывы:

Похожие инструкции для GLX-RSS-2-300 WL

Бренды по названию

Популярные бренды