Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 51

Страница: 51 / 137

D.Dismantling the step plates and lower

Mudguard:

1.Take off the screws of the four

step plates and take off the four

step plates.

2.Screwing out the screws of lower

mudguard.

E.Dismantling the step floor and front

inner cover:

1.screwing out the screws of battery

cover.

2.Disconnect the negative, then

positive cable.

3.Screwing out the screws between the

step floor and front inner cover

Take off the front inner cover.

4.Pull out both the negative and

Positive battery cables, Take off

The step floor.

5.When assembling, the procedures

Will be reversed.

M6:0.7-1.1kgf-m

M5:0.35-0.5kgf-m

Note:Avoid clamping and scraping the

Cables or pipes by the plastic parts.

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды