Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 35

Страница: 35 / 137

(3) Clean air cleaner

1.Remove air cleaner cover.
2.Take out the air cleaner filter.
3.Clean the filter by compressed air.
4.Assemble the air cleaner by the opposite procedure.

MOTOR OIL

Attn: Do not start engine when air cleaner is not installed.

Oil volume

Note:

A. The vehicle must park on the flat ground

Before checking.

B.Start engine for 2~3 min., and stop engine

For 2~3 min., then check the oil volume.

1.Take out the oil meter to check the oil

Volume.

2.Refill oil to upper limit when oil volume

Is below the lower limit.

Exchange Oil

1.Turn off the engine and remove the oil meter.

Oil meter

2.Screw out the oil draining bolt on the bottom

Torque:1.5kg-m

Lower limit

Upper limit

Note: The oil will flow out easier when the

engine is warm.

Engine oil volume :

Disassembling : 1.0 liter

Exchanging : 0.80~0.85lite

When checking the leakage of oil, start the engine
At idling for a few minutes, then check the oil volume.

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды