Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 137

background image

2.Testing the recharging performance

This test needs to be done under the
Battery has been recharged completely

a. This test needs to be done after
engine is warm-up.
    And take off the luggage case
    Firstly.
b. Disconnect the orange cable of
regulator.
c. Open the fuse box to remove the
white cable
d. Connect currency meter between red/
white cable fuse.

While testing, the red wire cable must not touch the frame.

d. Set the headlamp switch at “OFF” , engine rotation is at 2000 rpm while testing.
Then increase the rpm slowly.

Head Lamp Switch

Recharging rpm

2,500rpm

6,000rpm

OFF (DAY)

Under2,000upm

0.6A(MIN)

1.5A(MIN)

ON (NIGHT)

Under2,000upm

0.6A(MIN)

1.5A(MIN)

e. If the testing result does not match standard value, check the regulator.

125

«
...
127
128
129
130
131
...
»

Содержание Buddy 170










































































































































Отзывы:

Нет отзывов

Похожие инструкции для Buddy 170

Бренд: Qualisports Страницы: 8

Бренд: Yamaha Страницы: 77

Бренд: Skoot-Eze Страницы: 12

Ninebot Mecha Kit

Бренд: Segway Страницы: 45

ML-44GDRS-ES-E100

Бренд: MAXTRA Страницы: 17

Бренд: Flyer Страницы: 271

Бренд: F-Wheel Страницы: 8

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 76

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 67

Бренд: Yamaha Страницы: 45

Бренд: Yamaha Страницы: 74

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 66

Бренд: Yamaha Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды