Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 40

Страница: 40 / 137

(11) Rear Brake Adjustment

1.Check the clearance of rear brake lever.

Clearance: 10~20mm

2.If the clearance is beyond the above

Standard, adjust it by rotation the screw.
a. Left-handed rotation-Enlarge the clearance.
b. Right-handed rotation-Reduce the clearance.

Note: When the arrow of rear brake indicator align with the arrow of left crankcase, change

the brake lining.

(12) Tire:

1.Check Tire air pressure.
2.Tire pressure:

Front tire: 1.50kg/cm

Rear tire: 1.75kg/cm

3.Tire specification:

Front tire: 100/90-10
Rear tire: 100/90-10

Note:

1.Check and adjust the tire pressure when it is too low.

The pressure is according to the carrier, driver, passenger, accessories and cruise speed

2.Proper loading is very important for steering, riding, braking, performance and safety. Never

carry any parcel unfastened.
Load the heaviest parcel on the center of vehicle, balancing the weight on both sides.
Beware of the weight loaded properly and check the tire pressure. The total weight of carrier,

driver, passenger, and accessories cannot exceed the approved limit. An overload vehicle is
easy to cause tire damage and accident for rider

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды