Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 92

Страница: 92 / 137

(F)Front brake

1.Disassembling and assembling of the front

brake comp.

a.Remove two bolts fixed on the front brake

comp and the front fork.

b.Remove the front brake comp.

c.Assemble the front brake comp.

Follows the opposite procedure of dismantling.

Locking Torque:

M8: 2.0~3.0kg-m

2.Air releasing of the front brake comp

The procedure of air releasing

a.Fill the enough brake oil to the container

b.Do not let the brake oil overflow from the

master cylinder or container when assemble

the master cylinder cover.

c.Put the spanner upon the drain screw.

a. Lock and unlock the screw several times to

Release the bubbles.

b. Operate slowly the brake lever several

times.

c. Clamp the brake lever to the end.

d. Loose the drain screw, then open the lever completely.

e. Locking the drain screw and then loose it when the lever is opened completely.

f. Repeat above procedure until all the air in the brake system has been released

Completely.

Locking torque of leaking screw: 0.6 kg-m

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды