Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 60

Страница: 60 / 137

D.Starter dismantle

1.Dismantle left crankcase cover

2.Remove hexagon nut, then remove the starter lever.

3.Remove five screw of separated plate.

4.Remove start spring from

start returning positioner.

5.Remove driven gear comp. of

kick starter.

6.Remove the retaining C-type

Ring.

7.Remove spindle comp.

of kick starter.

8.Checking starter

a.Check the wearing condition of the outer diameter of spindle comp and the inner

diameter of bush and gear.

b.Check the wearing condition of shaft of driven gear comp. Gear sets and

ratchet.

9.Assembling the starter

Assemble the starter follows the.

Opposite procedure of dismantling.

Locking torque : M6:1.0~1.2kg/m.

Note:

Make sure one end of the torsion spring is

hooked on the groove of driven gear, and

another end of torsion spring is hooked on

the pole of inside of left crankcase.

Put some grease in every shaft and gear sets

before assembly.

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды