Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 87

Страница: 87 / 137

A.Troubleshooting

1.steering handlebar is abnormal, too tight.

a. steering mechanism; washer of conical bush locked too tightly.

b. steering mechanism; steel ball is cracked.

c. steering mechanism; steel ball base and washer of conical base is damaged.

d. wheel pressure is too low.

2.steering handlebar is aslant.

a.left and right damper is not even.

b.Front fork is crooked.

c.The axle of front fork is crooked, wheel is aslant.

3.front wheel swings.

a.wheel rim is distorted.

b.bearing of front axle too free.

c.wheel rib is distorted.

a. Wheel is not good.

b.Front wheel axle locked improperly.

4.front damper is too soft, spring fatigue.

5.noise in front damper.

a.noise comes from damper box.

b.locking screw of damper is slackness.

B.Data

Item

Standard value ( mm )

Limit of use ( mm )

Lining of frt brake

4.0

2.0

Disk of frt brake

3.6

3.1

Swingness of frt/rr wheel

2.0

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды