Genuine Scooter Company Buddy 170 Скачать руководство пользователя страница 45

Страница: 45 / 137

8.Remove oil pump separate plate by

taking off the 2 bolts.

9.Remove the bolts from oil pump

driving gear

10.Take off the driving gear and chain.

11.Remove the oil pump by taking off

the locking bolt of the oil pump.

Assembly

1.Install the inner and outer of the oil pump.

2.Install the oil pump shaft.

3.Install the lock pin.

4.Match the lock pin hole to the pump cover

and install the oil pump cover.

5.Put on the screws and tighten them.

6.After installing, turn the shaft lightly

to assure installation.

7.Place the oil pump into the carnkcase.

8.Tighten the oil pump after installation.

Note:
The notch of the oil pump shaft should comply
With the notch of the inner gear.

Note:

When installing, the arrow on the oil pump

body should be pointed upwards. Then fill in

the recommended oil before the installation.

Содержание Buddy 170










































































































































Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды

Genuine Scooter Company Buddy 170, Руководство по обслуживанию

Результаты поиска

Содержание Buddy 170

Отзывы:

Похожие инструкции для Buddy 170

Бренды по названию

Популярные бренды