15
[22]Miscellaneous Features 1
(1) Abort Delay - Program to allow a 15
second Delay (except
24 Hour Zones) after
a zone trip before reporting. Disarm the
system within 15 seconds to prevent report-
ing.
(2) Easy Exit/Easy Arm- Enables
command. While the system is
armed, entering this command allows 3 min-
utes to Exit through
Exit/Entry and Exit/Entry
Follower Zones. Enabling this option also
enables Easy Arm, press the
key to arm
the system.
(3) Swinger Shutdown - Automatically dis-
ables armed zones with excessive alarm/
restores (swingers). Non-24-Hour Protection
zones: allows only 3 alarms and 2 restores
per zone per arming before the zone is dis-
abled.
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
[23]Programmable Output Features 1
(1) Audio Verification - Program to activate
the PGM during reporting. Select specific
zones for audio verification by programming
the required zones in
PGM Output [08],
PGM Features 2 [24] and PGM Features 3
[25]. Connect the PGM to the Veriphone
TM
trigger low input.
(2) Access Output - Activates the PGM
output for 5 seconds using the
command.
(3) Follow Keypad Sounder - The follow-
ing keypad sounds will activate the PGM
output: Entry Sounder, Keypad Pulsing
Sounder, Keypad Output on Alarm, Chime,
Fault Find.
(4) Keyfob/Keyswitch Chirp - Program to
chirp the PGM Output (1) one time when
the panel is armed or (2) two times when
the panel is disarmed. Wire as shown in
Figure 7.
[24]Programmable Output
Features 2
(1) Fire - Program to activate the PGM on a
Fire alarm.
(2) AUX - Program to activate the PGM on
a AUX alarm.
(3) Panic - Program to activate the PGM on
a Panic alarm.
(4) Test Timer - Program to activate the
PGM during a Test Timer report.
[25]Programmable Output Features 3
(1) AC Fail - Program to activate the PGM on
the loss of AC. (15 minute delay)
(2) Low Battery - Program to activate the
PGM on a Low Battery condition.
(3) *Trouble - Program to activate the PGM
on a Trouble condition.
(4) Armed - Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Receiver
JAM, Wireless Smoke Low Battery, Wireless
Smoke Supervisory Fail.
[26]Miscellaneous Features 2
(1) Momentary Keyswitch Arming - Typi-
cally, connect a normally-open Keyswitch
across the zone AND its 3.3K zone-doubling
resistor.
(2) Reserved.
(3) Inhibit Fail-to-Communicate Display -
This option prevents the keypad from either
indicating or sounding when a Fail to Com-
municate has occurred.
(4) Inhibit Low Battery Display - Program
to inhibit the Low Battery Display at the
keypad. Low Battery Reporting is not inhib-
ited. The programming option is not permit-
ted for UL installations.
N/O
N/C
COM
BLK
RED
+AUX
Siren Driver
Steady Input
PGM
+AUX
K1
FIGURE
7 K
EYFOB
/K
EYSWITCH
C
HIRP
Wi850a
page 15
Tuesday, September 16, 1997 08:01
