Gemini GEM-P800 Скачать руководство пользователя страница 26

Страница: 26 / 28

WI850A GEM-P800 Installation Instructions

8. How do I remove Keypad Sounder on

Alarm?

The keypad sounder follows the Burg Out-

put. If you need to remove the Keypad

Sounder, then you must remove the Burg

Output from that zone.

9. Transmitters not responding?

Open Transmitter case - Keypad should go

into X-Mitter Tamper Trouble. If not:

Check Receiver Red LED should be

flashing once approx. once a second.

Check Receiver wiring.

Check Programming of Transmitter ID.

If Keypad does go into X-Mitter Tamper

Trouble, check:

Transmitter point is programmed cor-

rectly.

Transmitter is wired correctly:

If using external switch, make sure it is

wired to point 1, and point 2 is jumped

out.

If using internal reed, make sure J1 is

cut and both Point 1 and Point 2 termi-

nals are jumped out.

10. Keypad LEDs Flicker.

The Keypad is not receiving a POLL from

the Panel.

Check Keypad wiring.

1. The Panel is in the process of being

Uploaded/Downloaded.

2. The panel is powering up. LED’s

will flicker until panel has reset and

is polling the keypad.

3. The connection from the control

panel to the keypad is open.

11. No Keypad Entry Sounder during En-

try Time?

The keypad sounder is turned off with the

command. This command will

silence all Keypad sounds except keypad

sounder on alarm. Enter

turn keypad sounds back on.

12. No Keypad Chime?

The keypad sounder is turned off with the

command. This command will

silence all Keypad sounds except keypad

sounder on alarm. Enter

to turn

keypad sounds back on.

Wi850a
page 26

Tuesday, September 16, 1997 08:01

Содержание GEM-P800





























Результаты поиска

Содержание GEM-P800

Отзывы:

Похожие инструкции для GEM-P800

Бренды по названию

Популярные бренды

Gemini GEM-P800, Руководство по установке

Результаты поиска

Содержание GEM-P800

Отзывы:

Похожие инструкции для GEM-P800

Бренды по названию

Популярные бренды