Gemini GEM-P800 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

background image

22

WI850A GEM-P800 Installation Instructions

5. Enter Standby Mode by entering

R

.

The Computer is now in STANDBY

Site
At the site perform the following three steps:

1. Arm the panel.
2. Disarm the panel.
3. Enter

. The panel will now

call the download computer running
PCPreset. PCPreset will answer the
call, establish a connection, and then
download the account that matches the
Auto Download ID Number [93] with the
account of the same number in the list
that PCPreset is currently running.

'HDOHU 3URJUDPPLQJ

[94]Dealer Code

The default Dealer Code is

4567

. Program

a new 4-digit Dealer Code. When the panel
is defaulted the Dealer Code will be changed

back to the default Dealer Code of

4567

only

if Dealer Code Lockout [96-1] has not

been programmed.

[95]User 1 Code

The 1st User code is a program code as
well as an Arm/Disarm code. The default

User Code is

1234

. If User 1 Code Lock-

out is programmed the User 1 Code cannot
be programmed from User Program Mode.

[96]Dealer Options 1

(1) Dealer Code Lockout - Program to
prevent the Dealer Code from changing
with a panel default.
(2) User 1 Code Lockout - If programmed
the User 1 Code cannot be programmed
from User Program Mode.
(3) Household Fire - Activates the follow-
ing UL required features:
There is a 4 hour re-sound of wireless
Smoke Low Battery and wireless Smoke
Supervisory system troubles.

•

An active System Battery test per-
formed every 4 hours instead of 24
hours and Wireless Smoke Supervisory
Timer is set to 4 hours.

•

Fire Bell Timing is March Time.

•

Wireless Smoke Supervisory Time is
fixed at 4 hours.

(4) Fire Trouble on Fire LED - Normally
all troubles are displayed on the

SYS-

TEM TROUBLE LED, including Fire Trou-
ble. If required Fire Trouble can be dis-

played on the Fire LED. Fire Trouble is
indicated by a steady

Fire LED.

[97]Dealer Options 2

(1) International Dialing Protocol - No dial-
ing if no dial tone, 60 s between attempts
and 4 s wait for dial tone.
(2) Invert Bell Output - Inverts the Bell
polarity and removes supervision from the
bell circuit.
(3) System Trouble Auto Restore - Nor-
mally, System troubles require acknowledg-
ment (View System Trouble) in order to re-
store. If this option is selected troubles will
restore without requiring acknowledgment.
(4) User 1 Code-Program only - If enabled
User 1 Code will function only as the User
Program Code and will not Arm/Disarm the
panel.

Note: All programming within Programming
Blocks [96] & [97] will not

change if the panel

is defaulted.

[98] Number of Re-Dials

The Number of re-dial attempts made by the
panel before indicating a

Fail-to-

Communicate

(System Trouble 1-3).

Wi850a
page 22

Tuesday, September 16, 1997 08:01

«
...
20
21
22
23
24
...
»

Содержание GEM-P800





























Отзывы:

Нет отзывов

Похожие инструкции для GEM-P800

BL-C1A - Network Camera

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 8

Бренд: Fender Страницы: 3

Бренд: Yamaha Страницы: 83

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 14

Бренд: Yamaha Страницы: 10

Бренд: Yamaha Страницы: 50

Бренд: Yamaha Страницы: 8

Бренд: NEO TOOLS Страницы: 17

Бренд: Bose Страницы: 44

Бренд: Gemini Страницы: 10

Бренд: Velleman Страницы: 22

Бренд: X-10 Страницы: 18

Бренд: RAM Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды