background image

 

34

 

Sub Meters 

GE Multilin 

The panel or housing in which the EPM 2000 is mounted, should protect it from dust, 

moisture, oil, corrosive vapors, etc. 

 

The panel doors must be easily opened to provide easy access to the EPM 2000 wiring for 

trouble-shooting. Allow clearance if the unit is going to swing out, as well as adequate slack 

in the wiring. Allow space for terminal blocks, CT shorting blocks, fuses, auxiliary 

contractors and other necessary components. 

4.1.2.3. 

Viewing 

For ease of operation, in the location should be preferably at, or slightly above, eye-level. For 

viewing comfort, minimize glare and reflections from strong light sources. 

 

4.1.3. Mounting 

Before Mounting and Wiring, the 

Setup procedure

 should have been completed. 

 

The EPM 2000 is panel mountable. 
             Panel cutout                             :90+1.0-0 mm (w) x 90+1.0-0 mm(h)   DIN 43700 

             Panel Thickness                       : 0.5 mm to 4.0 mm. 

             Instrumental Bezel dimension  : 96 mm x 96mm 

             Depth behind Bezel                  :80 mm. Leave clearance for wires.      

                                                                82 mm with Terminal Cover 

             

Mounting Clamp Screws          :  Slotted, 2 nos. 

             Terminal Screws                       :Combination Phillips & Slotted head 

 

The cut-out should be punched with the proper tool and should be free from burrs. 

 

Before Wiring, insert the EPM 2000 into the cut-out from the front. Then, fasten the two side 

clamps from the rear. While supporting the EPM 2000 from the front, tighten both side clamp 

screws in a criss-cross pattern till all slack is taken up, then apply one full turn. Do not over-

tighten. 

 

 

Содержание Multilin EPM 2000 Series





















































Отзывы: